Free Delivery   Over   £50  * terms * Most UK Addresses
|
Order Today For Dispatch On or Before  Monday 23 November

How to Tape Up the Back of a Frame

Why framers tape up the back of a picture frame, and what it does: keeps out dust and insects, holds everything in place and gives a neat finish. Includes a video.

By EasyFrame, Bedford. Updated October 2026. 2 minute read.

Professional framers tape up the back of every frame as a matter of course. It looks like a minor detail, but it does a lot to protect what's inside, and it only takes a few minutes.

How to tape up the back of a frame

Video: how to tape up the back of a frame.

Prefer our earlier video? Watch “How To Tape Up The Back Of Your Frame” on YouTube.

Why tape up the back?

  • Keeps out dust: it stops dust, dirt and airborne particles getting into the frame, so your artwork stays clean.
  • Keeps out insects: it seals out silverfish, moths and other pests that can damage paper, photos and mounts.
  • Holds everything in place: it keeps the backing board, mount and artwork secure, so they're less likely to shift or warp as the humidity changes.
  • A moisture barrier: good archival tape helps keep humidity out, which matters most for valuable and delicate pieces.
  • A professional finish: it covers the fixings and raw edges, so the back of the frame looks neat.
The back of a frame, with its backing board, and why to tape it up.
The back of the frame, before taping.

Step by step

1. Check the flexible tabs

Your frame comes with flexible tabs already fitted: they're fixed in the frame's rebate about every 100mm, and lie over the edge of the backing board to hold it in. The tape goes over them, so check they're all pressed down flat first.

The back of the frame, with flexible tabs all round holding the backing board in.
The flexible tabs, already fitted all round.

2. Get ready

Lay the frame face down on a clean surface. You'll need brown framing tape (self-adhesive kraft tape, or archival tape for valuable pieces) and a craft knife or sharp scissors.

The frame face down, with brown framing tape and a craft knife listed.
Face down, ready to tape.

3. Tape the first side

Run the tape along one side, over the join: half on the frame and half on the backing board, running a little past each corner. Smooth it down firmly as you go.

A strip of brown tape along the top side, over the join between the frame and the backing board.
Half on the frame, half on the board.

4. Do all four sides

Tape the other three sides in the same way, smoothing each one down firmly over the tabs.

Tape along all four sides, the ends crossing at the corners.
All four sides taped.

5. Trim the corners

Trim the ends of the tape neatly at the corners with a craft knife, so nothing overhangs the edge of the frame.

The tape trimmed neatly at each corner.
Trimmed at the corners.

6. Fit the hanging fixtures

Screw a D-ring to each side, about a third of the way down, and tie the cord between them.

D-rings a third of the way down each side, with a cord between them.
D-rings and cord, ready to hang.

If one side is bowed

Now and then a long side of a frame has a slight bow, so it curves away from the backing board, leaving a gap along that side and lifting that side's tabs off the board. Taping it up the usual way would hold the bow in. Instead, straighten the side first, and let the tabs and tape hold it straight.

  1. Spot the gap: look along each side for a gap between the frame and the backing board. (It's shown larger than life here: a bow is often only a millimetre or two.)
  2. Straighten it: press the middle of the bowed side gently in, until it sits straight against the backing board, and keep holding it there.
  3. Secure it: still holding it, press that side's tabs down flat onto the backing board, then tape it from the middle out to each corner. Once the tape's on, you can let go: the tabs and tape hold the side straight.
  4. Finish: tape the other three sides as before, and trim all four corners.
A frame with its top side bowed outwards, leaving a gap between it and the backing board.
A bowed side, and the gap it leaves.
The middle of the bowed side pressed in until it's straight.
Pressed straight.
The straightened side, its tabs back over the board, taped from the middle out.
Tabs and tape hold it straight.
All four sides taped and trimmed.
All four sides done.

Taping up the back is a simple step that improves the protection, the look and the life of a frame. Whether it holds a family photo or a valuable piece of art, it's worth the few extra minutes.

Questions? Our team is always happy to help: email sales@easyframe.co.uk, or call 01234 856501.

Ready to frame yours?

Print and frameUpload a digital photo and we print and frame it for you. Multi print and frameSeveral photos, printed and framed together in one mount. Already have prints?Order a frame and mount made to measure for them.

Popular frame sizes: A4 picture frames, A3 picture frames, 10x8 photo frames, 8x6 photo frames, 50x70 poster frames, 30x40cm frames, gold picture frames and multi photo frames.

Questions? Call 01234 856501 or email sales@easyframe.co.uk.

More how-to guides

How to Attach Artwork to a Mount How to Clean Acrylic Glazing How to Fit a Canvas Board in an Inset Frame See all how-to guides
Software: Kryptronic eCommerce, Copyright 1999-2026 Kryptronic, Inc. Exec Time: 0.004388 Seconds Memory Usage: 1.655479 Megabytes
EasyFrame - Picture Framing Made Easy EasyFrame.co.uk